R&R Tech
- Author: Lance Baker
- Subject Matter: Diagnosis
- Unit: 5R110W
- Vehicle Application: 2007 Ford F-350
- Issue: Damage to pump gears
The 5R110W transmission that is common to the 2003-2009 Ford Super Duty trucks and vans is a very reliable and straightforward transmission when it comes to diagnosis and repair. The subject of this article is a 2007 F-350 equipped with the 6.0L diesel engine and the 5R110W transmission.
This truck came into our shop diagnosed with an internal problem that required the transmission to be removed and repaired. The decision was made to go with a remanufactured unit in lieu of repairing the customer’s unit, since the vehicle was a commercial truck and the customer was in a hurry to get it back on the road. The transmission was replaced with our remanufactured unit, the vehicle software calibration was updated, fluid level was verified and the relearn procedure was performed.
After a road test and a recheck, the truck was delivered to the customer with a 15-day follow-up recommendation, which is our standard protocol after an installation to ensure that there are no leaks or problems that could lead to future issues for the customer. When this truck came back for the 15-day follow-up, everything was working great and the customer was pleased with the job.
Several months later, this truck was returned to our shop on a flatbed, and when we attempted to drive the vehicle it would not move in either forward or reverse. We got it into the shop right away and began the diagnostic process to find the source of the problem.
A scan of the computer showed no codes, and a fluid check showed the fluid was clean but overfilled. We again verified that the truck had no forward or reverse gears. It was determined that there was a problem with the pump, so we elected to replace the transmission under warranty.
When this unit was returned to the factory, a complete teardown and inspection took place. After the transmission was disassembled, it was found that the inner pump gear was broken (Figure 1) and welded to the pump plate, but all other components of the transmission were in great shape.
Further inspection revealed that the pump plate showed signs of etching (Figure 2). This isn’t that uncommon; about 30% of the core transmissions we get come in with signs of pump-plate etching.
After this discovery, we placed a phone call to the owner of the truck to inform him that we needed to get his truck back into the shop to check a few things out so a future failure could be avoided. An appointment was made, and the truck returned a few days later. This is when the real work began.
We first started with a computer scan. There were no codes stored or pending, so a road test followed. We took this truck on an extensive drive, and it performed and shifted perfectly. Next, a full inspection of the cooling system took place; we wanted to make sure there were no cooler-flow problems, so a flow test was performed and everything there passed testing.
Finally, we decided to perform a full diagnosis of the electrical system. We checked the charging system and load-tested the battery and alternator, and everything passed inspection. We decided to clean the battery terminals as a precautionary measure. We then decided to check the body and chassis grounds. We found several grounds that looked extremely corroded, and they were green. We also noted that this truck looked as though it had seen several bad winters of road salt, as the undercarriage showed extensive corrosion.
As the inspection progressed, we found a body ground that literally fell apart in our hands. Most of the body grounds we checked were green and corroded and in poor functioning condition. An ohmmeter revealed that several of these grounds had more than 20 ohms of resistance. The bad grounds were either repaired or replaced, and a redundant ground strap was added between the transmission case and the chassis to ensure that a solid grounding path was in place.
What does this have to do with the pump failure and etching that were found during the failure analysis? Voltage is stubborn; it desperately wants to find a path back to its home: the battery. The vehicle manufacturers do a great job of providing ample pathways for that voltage to make its way back to the battery through the ground connections and wires. On a new truck, these work fine. On a truck like the subject vehicle, one that has aged and experienced a corrosive winter environment that has compromised those wires and connections, many different (and sometimes strange) issues can arise because of it.
In our case, the voltage return paths were compromised. The transmission pump, in essence, became the path of least resistance. Similar to what happens during cavitation that results from electrolysis, the plate in the pump became etched by the transfer of electricity within the pump. That transfer also occurred between the pump gears and ultimately caused them to fail (Figure 3). The redundant grounding strap that we added eliminates this possibility permanently, even if the other ground wires were to corrode and fail again over time.
Since the time that this truck was repaired under warranty, it has not returned to our shop. The owner has contacted us to let us know that he is pleased with the job and that the transmission shifts better than ever. Just remember that the next time you are chasing down electrical gremlins in a vehicle, bad grounds can be the cause of many problems, and commonly so.
Lance Baker, warranty technical adviser, joined Certified Transmission in early 2013 and works closely with customers’ shops and distributors. His technical background allows him to assist customers with pre-installation and post-installation questions and warranty concerns. He also works with internal teams to develop installation instructions for Certified’s products to help customers provide the best possible installations.
