Nissan RE0F11A CVT transmission speed sensor codes, part 2

Main Navigation

Advertisement
Social Connect
Resources
Our Brand Family
Transmission Digest - Babcox Media
Helping transmission shops achieve successful and profitable operation.
Technical

Nissan RE0F11A CVT transmission speed sensor codes, part 2

Wayne Colonna
By Wayne Colonna
Published:
RE0F11 Figure 1

The complaint

All Nissan vehicles using the RE0F11 (CVT7) CVT Transmission may have a complaint of P0715 “Input Speed Sensor A Circuit” stored after overhaul. (They may also have the complaint of P2765 “Input Speed Sensor B Circuit” stored, as seen in our other article).

Related Articles

The cause

The input speed sensor “A” exciter wheel is attached to the primary pulley sheave and is comprised of a number of fingers that are made of soft metal. The fingers can be easily bent from handling during the disassembly or reassembly process, as seen in figure 1 at the top of the page. If the fingers are bent enough to increase the allowable air gap between the exciter wheel and the tip of the speed sensor, then trouble code P0715 will be stored.

The correction

Using a dial caliper, take a measurement from the exciter wheel finger to the speed sensor mounting area of the transmission case as shown in figure 2.

RE0F11 Figure 2
Figure 2.

Then measure the speed sensor from its mounting surface area to the tip of the sensor as seen in figure 4. Subtract one measurement from the other. The distance should be not more than .040 in.

RE0F11 Figure 3
Figure 3.

If the measurement is greater than .040 in. the finger will have to be bent into specification. This procedure will have to be performed with each exciter wheel finger that is out of specification.

You May Also Like

Figure 12.
CVT-Transmission-2
Featured

Shift of the shaft: Diagnosing Chrysler 48RE manual shaft issues

The TorqueFlite transmission has been around since mid-to-late 1950s. There have been many changes surrounding the manual shaft and rooster comb through the years. This transmission shaft controls the position of the manual valve that directs oil for the gear ranges, but it also is used for a Reverse light control as well as Park/Neutral

Randall Schroeder
By Randall Schroeder
Randall Schroeder is a Sonnax technical specialist and member of the Sonnax TASC Force (Technical Automotive Specialties Committee), a group of recognized industry technical specialists, transmission rebuilders and Sonnax Industries Inc. technicians.
Published:

The TorqueFlite transmission has been around since mid-to-late 1950s. There have been many changes surrounding the manual shaft and rooster comb through the years. This transmission shaft controls the position of the manual valve that directs oil for the gear ranges, but it also is used for a Reverse light control as well as Park/Neutral safety control. As it evolved, changes to these safety backup switches caused extra stress against the rooster comb that posed new challenges to the technician. 

Read Full Article

More Technical Posts
Sometimes, a diagnostic code is all you need

With ATSG having the opportunity to help shops solve problems, sometimes we get faced with some real doozies. A shop will call and give us a laundry list of DTCs, leaving us to think someone must have a bulkhead connector unplugged. We then go through the arduous task of deciding which codes prompted other codes

By Wayne Colonna
10L80 and 10R80 pump gear differences

You may have seen an article in the August 2023 issue of Transmission Digest called “GM 10L80: A new kind of pump noise,” which goes over how the front cover housing in the 10L80 is fitted with a converter drive gear and idler gear. The idler gear drives the pump’s driven gear, and is press

By Wayne Colonna
Shift Pointers: What to do when the 62TE TRS tab breaks

How frustrating it is when on a hot summer day, as you go to open a nice cold can of your drink of choice, and the tab breaks off? You are outside, away from any tools to remedy the problem quickly. It now requires a MacGyver mentality looking around at the resources available to get

By Wayne Colonna
Going the extra mile: Proving your transmission repair suspicions

A 2003 Honda Pilot with a five-speed three-shaft transmission came into our shop with a customer concern that the vehicle had no power, and the “D” light was flashing. I first did a scan for codes to see what it came up with, and the scan tool returned four DTCs: P1298 (ELD voltage high), P0135 (H02S

By Paul Loch
RRfeature-1400

Other Posts

Spotting different 68RFE designs through the years to avoid issues

The Chrysler 68RFE has had several changes through the years. Its four-speed predecessor began with a noisy solenoid pack identified by a black colored pass-through case connector (seen in Figure 1).  Related Articles – Outgrowing the walls: The story of EVT Transmission Parts – Valve body and component suppliers: A comprehensive list – Shift Pointers:

By Wayne Colonna
Shift Pointers: Failures caused by incorrect tire sizes

For years ATSG has produced a wide range of issues related to improper tire sizes on vehicles. Even under-inflated tires have been known to cause issues. Problems such as premature failure with an active 4WD transfer case will occur with incorrect tire sizes. Related Articles – Understanding lube flow control valves in Toyota/Lexus UA/UB80 transmissions

By Wayne Colonna
Shift-Pointers-Jan-Figure-1-1400
Understanding lube flow control valves in Toyota/Lexus UA/UB80 transmissions

The Toyota/Lexus UA80 and UB80 transmissions first came out in 2017 in Highlanders and Siennas. The UA80 is used in V6 applications, and the UB80 is paired with four-cylinder versions. They have been called Toyota New Global Architecture type transmissions, and alternately referred to as the “Direct Shift 8AT” eight-speed automatic transmission. This transmission was

By Jim Dial
Tasc-Tip-December-Figure-1---LFC-Valve-OE-Partial-Circuit-Diagram-1400
How reading through service bulletins can turn a technician into the customer’s hero

Over the last 28 years of being a technician, I have developed the habit of checking for and reading technical service bulletins at the forefront of the diagnostic process, especially when an unfamiliar vehicle exhibiting blatant or straightforward concerns comes into the shop. I have found many valuable nuggets of information while reading over these

By Kevin Wayne