Honda Accord BB7A six-speed: P2720 code set after collision - Transmission Digest

Main Navigation

Advertisement
Social Connect
Resources
Our Brand Family
Transmission Digest - Babcox Media
Helping transmission shops achieve successful and profitable operation.
Transmission TECH/TALK

Honda Accord BB7A six-speed: P2720 code set after collision

Wayne Colonna
By Wayne Colonna
Published:
Tech-Talk-Aug-Figure-1-1400

The complaint

A 2015 Honda Accord with a 3.5-liter engine and the BB7A six-speed transmission (seen in figure 1, above), was involved in a minor collision to the left front of the vehicle. The vehicle was drivable and was taken to the transmission shop. Vehicle diagnostics revealed a P2720 “Pressure Control Solenoid D Voltage Low” was set and a no-reverse condi­tion was also present.

Related Articles

The cause

Further diagnostics revealed that PCS D is on in reverse as seen in the solenoid application chart in figure 2.

Tech-Talk-Aug-Figure-2-1400x1000
Figure 2.

As a result of the collision, the battery tray was driven towards the transmission where the externally mounted solenoids are located. This resulted in the Solenoid D connector being broken, as you can see in figures 3 and 4, and causing the code to set and the no reverse condition.

Tech-Talk-Aug-Figure-3-1400
Figure 3.
Tech-Talk-Aug-Figure-4-1400
Figure 4.

The correction

The solenoid body and battery tray were replaced which allowed the P2720 to be cleared, after which reverse functioned normally.

Read more articles in our Transmission Tech/Talk series here.

You May Also Like

Figure 1.
Tech-Speak-April-Figure-1-1400
Featured

Don’t fear customer complaints about CVTs

Continuously Variable Transmissions, or CVTs, are more common than you think. Audi, Subaru, Nissan, Ford, GM and many other automakers use CVT transmissions in cars and SUVs. There is no way to avoid them. Chances are there is one in your shop right now. What does CVT mean for technicians? On the maintenance side, a

Andrew Markel
By Andrew Markel
Andrew Markel is an ASE Certified Technician and former service writer, and is now director of content for TD's sister sites, Import Car, Shop Owner and Brake & Front End.
Published:
CVT-Transmission-2

Continuously Variable Transmissions, or CVTs, are more common than you think. Audi, Subaru, Nissan, Ford, GM and many other automakers use CVT transmissions in cars and SUVs. There is no way to avoid them. Chances are there is one in your shop right now.

What does CVT mean for technicians? On the maintenance side, a CVT requires more or the same frequency of fluid and filter changes as a conventional automatic transmission, and many of the basic procedures are the same. On the diagnostic side, a CVT is less complicated internally than a six- or nine-speed transmission. Diagnostics with a scan tool are about the same. On the service side, while you may never pull a variator or belt out of a CVT, you can service components like sensors, pumps and valve bodies. The point here is not to fear a customer complaint about a CVT. 

Read Full Article

More Transmission TECH/TALK Posts
Jatco JF613E transmission quick reference material

For those working on the Jatco JR613E transmission, a widespread transmission with plenty of applications, the following should be a helpful guide. Related Articles – 2024 State of the Powertrain Industry – Powertrain industry directory and buyer’s guide 2024 – Shift Pointers: A Chrysler 300 no-shift complaint Domestic and international applications for the JF613E (also

By Wayne Colonna
Looking for the cause of repeated 6T40 torque converter failure

The converter clutch was applied just enough to drag but not enough to kill the engine.

By Wayne Colonna
Tech-Talk-Q4-Figure-4-1400
6T40 delayed engagements after overhaul

The problem lies in the compensator piston that a generation two clutch housing uses compared to the generation one housing.

By Wayne Colonna
Tech-Talk-Q4-Figure-7-1400
GM 6T70/75 slips and delays in first

A 2015 Chevrolet Equinox equipped with the 3.6-liter engine and 6T75 transmission has complaints of a delayed engagement into drive and slips in first gear.

By Wayne Colonna
Tech-Talk-Q4-Figure-11-1400

Other Posts

A guide to common GM, Ford and Nissan programming issues

One of the most common complaints I hear from shops when trying to install a new GM TCM is, “The module will not communicate.” While that might be partially true, by design they won’t communicate until they are programmed. If programming fails, there will be an “E” code set which will help you get to

By Peter Fink Jr.
Shift of the shaft: Diagnosing Chrysler 48RE manual shaft issues

The TorqueFlite transmission has been around since mid-to-late 1950s. There have been many changes surrounding the manual shaft and rooster comb through the years. This transmission shaft controls the position of the manual valve that directs oil for the gear ranges, but it also is used for a Reverse light control as well as Park/Neutral

By Randall Schroeder
Sometimes, a diagnostic code is all you need

With ATSG having the opportunity to help shops solve problems, sometimes we get faced with some real doozies. A shop will call and give us a laundry list of DTCs, leaving us to think someone must have a bulkhead connector unplugged. We then go through the arduous task of deciding which codes prompted other codes

By Wayne Colonna
10L80 and 10R80 pump gear differences

You may have seen an article in the August 2023 issue of Transmission Digest called “GM 10L80: A new kind of pump noise,” which goes over how the front cover housing in the 10L80 is fitted with a converter drive gear and idler gear. The idler gear drives the pump’s driven gear, and is press

By Wayne Colonna