Nissan RE0F11A CVT transmission speed sensor codes, part 1

Main Navigation

Advertisement
Social Connect
Resources
Our Brand Family
Transmission Digest - Babcox Media
Helping transmission shops achieve successful and profitable operation.
Technical

Nissan RE0F11A CVT transmission speed sensor codes, part 1

Wayne Colonna
By Wayne Colonna
Published:
Nissan RE0F11A

The complaint

All Nissan vehicles using the RE0F11 (JF015E-CVT7) CVT Transmission may have a complaint of P2765 “Input Speed Sensor B Circuit” stored. (They may also have the complaint of P0715 “Input Speed Sensor A Circuit” stored after overhaul, as seen in our other article).

Related Articles

The cause

The input speed sensor “B” exciter wheel is pressed onto the upper sheave of the secondary pulley. The exciter wheel can become loose and start to spin around freely. This will create an erratic signal which will result in the P2765 code being generated.

The correction

Gently tap the secondary speed sensor exciter wheel down on the pulley sheave. Then solder the exciter wheel to the pulley sheave in equally spaced areas as seen in the image above, do not use excessive or prolonged heat to avoid pulley damage. This will prevent the exciter wheel from coming loose again.

You May Also Like

Figure 1.
Tech-Speak-April-Figure-1-1400
Figure 12.
Featured

Shift Pointers: A Chrysler 300 no-shift complaint

The case study has to do with a 2009 Chrysler 300 C 5.7L Nag1 RWD with 71,923 miles on it (see Figure 1, above). It is based on a second opinion where a customer’s instinct combined with family member’s urging to seek a second opinion saved this customer a significant amount of money. First, a

Bill Harris
By Bill Harris
General Manager, Deltrans Inc.
Published:

The case study has to do with a 2009 Chrysler 300 C 5.7L Nag1 RWD with 71,923 miles on it (see Figure 1, above).

It is based on a second opinion where a customer’s instinct combined with family member’s urging to seek a second opinion saved this customer a significant amount of money.

Read Full Article

More Technical Posts
A guide to common GM, Ford and Nissan programming issues

One of the most common complaints I hear from shops when trying to install a new GM TCM is, “The module will not communicate.” While that might be partially true, by design they won’t communicate until they are programmed. If programming fails, there will be an “E” code set which will help you get to

By Peter Fink Jr.
Shift of the shaft: Diagnosing Chrysler 48RE manual shaft issues

The TorqueFlite transmission has been around since mid-to-late 1950s. There have been many changes surrounding the manual shaft and rooster comb through the years. This transmission shaft controls the position of the manual valve that directs oil for the gear ranges, but it also is used for a Reverse light control as well as Park/Neutral

By Randall Schroeder
Sometimes, a diagnostic code is all you need

With ATSG having the opportunity to help shops solve problems, sometimes we get faced with some real doozies. A shop will call and give us a laundry list of DTCs, leaving us to think someone must have a bulkhead connector unplugged. We then go through the arduous task of deciding which codes prompted other codes

By Wayne Colonna
10L80 and 10R80 pump gear differences

You may have seen an article in the August 2023 issue of Transmission Digest called “GM 10L80: A new kind of pump noise,” which goes over how the front cover housing in the 10L80 is fitted with a converter drive gear and idler gear. The idler gear drives the pump’s driven gear, and is press

By Wayne Colonna

Other Posts

Easy TH400, 4L80-E reverse servo setup: Craft your own tool

While not as sensitive as some shifting bands, the Reverse band adjustment on a TH400 or 4L80-E transmission is critical, and failure to get it right has tripped up even the best builders. There is nothing worse than getting the transmission installed, putting it in Reverse and then not going anywhere or having no engine

By Caleb Perham
Spotting different 68RFE designs through the years to avoid issues

The Chrysler 68RFE has had several changes through the years. Its four-speed predecessor began with a noisy solenoid pack identified by a black colored pass-through case connector (seen in Figure 1).  Related Articles – Valve body and component suppliers: A comprehensive list – Shift Pointers: Failures caused by incorrect tire sizes – Understanding lube flow

By Wayne Colonna
Shift Pointers: Failures caused by incorrect tire sizes

For years ATSG has produced a wide range of issues related to improper tire sizes on vehicles. Even under-inflated tires have been known to cause issues. Problems such as premature failure with an active 4WD transfer case will occur with incorrect tire sizes. Related Articles – How reading through service bulletins can turn a technician

By Wayne Colonna
Shift-Pointers-Jan-Figure-1-1400
Understanding lube flow control valves in Toyota/Lexus UA/UB80 transmissions

The Toyota/Lexus UA80 and UB80 transmissions first came out in 2017 in Highlanders and Siennas. The UA80 is used in V6 applications, and the UB80 is paired with four-cylinder versions. They have been called Toyota New Global Architecture type transmissions, and alternately referred to as the “Direct Shift 8AT” eight-speed automatic transmission. This transmission was

By Jim Dial
Tasc-Tip-December-Figure-1---LFC-Valve-OE-Partial-Circuit-Diagram-1400