In this Issue:
VW Touareg: Shift Interlock & Stop Lamps Inoperative
Kia Borrego: A5SR2 Transmission
Kia Borrego: A5SR2 TCM Upgrade
A Volkswagen Touareg may have a complaint of not being able to move the shift lever out of the park position. Further diagnostics reveals that the shift lock solenoid is inoperative and the stop lights are not illuminating.
- The brake light switch is faulty.
- The wiring that supplies power to the brake light switch under the driver’s foot rest has been damaged.
- Replace the brake light switch. The problem is finding it! Depending on when the vehicle was built, will dictate where to look for the switch.
A – Early built vehicles will have the switch in the usual place on the brake pedal (Figure 1).
B – Later built vehicles will have a pressure switch that screws into the brake master cylinder (Figure 2).
C – Late built vehicles have a pressure sensor built into the ABS pump assembly and will communicate the stop lamp ON signal over the CAN BUS network (Figure 3).
On early and later built vehicles you will be able to replace just the brake light switch or pressure sensor.
On later built vehicles the ABS pump and modulator assembly will have to be replaced.
- Pull back the carpet on the driver’s side and repair the wire damage that is found (Figure 4). It could be crushed from the driver’s heel or there could be corrosion from water intrusion.
A call came in to ATSG’s technical help line concerning a 2009 Kia Borrego with a 3.8L engine using a 5-speed RWD transmission called the A5SR2. This transmission is very similar to the Subaru 5AT transmission; a derivative of Nissan’s RE5R05A transmission. Mounted on top of the valve body are the solenoids, a sub-ROM and pressure switch frame assembly (Figure 5).
This A5SR2 came into the shop in 4th gear failsafe. The codes pulled were P0732, P0733 and P0734 gear ratio codes along with a P0763 Direct Clutch (D/C) solenoid performance code. With the direct clutch being applied for 2nd, 3rd and 4th gear, the D/C solenoid performance code was set as a companion code to the gear ratio codes set for those gear ranges. Kia’s description of P0763 is as follows: P0763 is not only caused by electrical malfunction (circuits open or shorted) but also by a mechanical malfunction such as control valve sticking or improper solenoid valve operation.
Since P0763 could be an electrical problem as well as a mechanical problem, it was decided to make an electrical check of the solenoid first before taking out the valve body. A wiring diagram was pulled which revealed that by placing an ohm meter between terminal 4 and chassis ground would provide the resistance of the D/C solenoid (Figure 6). The specification for this solenoid is three to nine ohms. When the check was made, it appeared to have an open circuit. In fact, when other solenoids where checked they too showed open. Thinking there is an internal harness problem, the valve body assembly was removed to inspect the wiring harness.
It was discovered that the cause for the open solenoid circuits had nothing to do with the codes being set placing the transmission into failsafe. Upon checking the wiring circuit it revealed an added component not mentioned in any tech material from Kia. The solenoid ground wires which are usually fastened to the valve body are now entering a 3/4″x3/4″x3/8″ black block mounted on the valve body (figures 7 and 8). Exiting the block are two other wires which passed through terminals 5 and 10 of the case connector. These two wires find themselves at terminals 29 and 73 at the TCM. To add to the confusion, when looking at wiring diagrams it says and shows that these two wires are “Solenoid Supply” wires going to two unknown solenoids inside the transmission. This did not accurately reflect what was actually inside this particular transmission. These two wires are actually ground wires for the solenoids from the TCM not power wires. The black block serves as a splice pack.
A resistance check was made across this splice pack which showed a 1.5 ohm resistance for each solenoid circuit. This needs to be taken into account when checking solenoid resistance through the case connector. Use terminal 5 and 10 for one meter lead and the other for each of the solenoids. Terminal 5 is the ground circuit for the D/C solenoid (4), the PL solenoid (8) and the LU solenoid (9). Terminal 10 is the ground circuit for the remaining four solenoids.
The cause for the codes to set were lightly tightened valve body bolts. The owner of the vehicle said the transmission was never worked on prior to this occasion. This suggests that the valve body was not properly tightened from the factory and eventually became a problem.
After all valve body bolts were tightened to 8 N·m (70 in.lb.), including the valve body to case bolts, the vehicle was road tested and the problem was resolved.
NOTE: It has been confirmed that 2008 to 2009 Kia Sorento using a 3.8L engine also has this splice pack and incorrect OE wiring. It may be earlier as well but have not been able to confirm.
The customer may complain of one or more of the following symptoms:
1. The vehicle hesitates or lags when shifting into to drive or reverse from the park position.
2. It lacks acceleration during the 1-2-3-4 up-shifts.
3. A shift delay or loss of power from 40 to 45 mph range.
Some 2009 Borrego (HM) with 3.8L engines produced from job #1 to January 15, 2009 may have these customer complaints which will require programming to resolve.
Available from Kia is a TCM UPGRADE: Shift Delay and Shift Quality Enhancements re-program. This upgraded logic will reduce customer complaints related to shift quality. When the re-flash is complete the TCM adaptives and Sub-ROM must be reset.
The re-flash makes the following remedies:
1. Increased adjustment of adaptive control values.
2. Increase the timing of up-shifts with over 40% APS input.
3. Shorten shift timing during 5-4 kick-down during medium/low speed zone.
Service Information:
TCM P/N ROM ID
Previous New
95440-4C800 THM0C38NAA THM0C38NAF
THM0C38NAB
THM0C38NAC
THM0C38NAD
95440-4C801 THM0C38NAE
UPGRADE EVENT NAME: 94. HM 3.8 09MY TCM: 95440-4C800/801
O.E. Information:
Campaign SA 016 – TCM Update For Shift Delay/Enhancement
Model Borrego[HM]
Group Automatic Transaxle[52]
Number KT200110303
Date Thursday, December 03, 2009
Area N.America
