Can you jump-start an EV? - Transmission Digest

Can you jump-start an EV?

Here’s a real-world scenario: A customer brings their EV into your shop for service, and it’s been there for quite a while because the parts are on backorder. After a few weeks, you get in the vehicle to move it out of your way, and the ignition won’t turn on. It’s acting like the battery is dead, so what do you do now?

Chances are that the low voltage or LV, or 12V, battery inside that EV has gone dead. In most cases, the LV battery is not charged while the high voltage (HV) battery is plugged into the wall charger. So, even if your shop is outfitted with an HV wall charger, the LV battery could still go dead if it’s left alone long enough.

This scenario can present a few unique challenges to us as techs or shop owners. The first question we need to ask ourselves is, “Can I jump this EV with another car?” We would advise against this idea. It’s much safer to have a dedicated battery jumper, preferably one with some electronic assist to protect the system from surges, inverse polarity, etc. Compact battery jump packs are available and are really handy for all kinds of situations.

Now you need to find the LV battery, and it could be anywhere in the vehicle. This of course will vary from one EV to the next, but the most common locations would likely be under the hood or in the trunk. But, herein lies another challenge — some EVs, specifically Teslas, have electronic door poppers which release the trunk and the hood, AKA the front trunk or frunk. So, it sort of turns into a “chicken before the egg” situation. How can you open the hood to get to the LV battery and jump it, if there’s no 12V power to actually open the hood?

Fear not, because Tesla thought this one out. There is a pair of wires that are located just behind the front tow hook cover in the front bumper cover. With a 12V battery jump pack on hand, press firmly on the top right perimeter of the tow hook cover until it pivots inward, then gently pull the raised section out toward you. Pull the two wires out of the tow eye opening and connect them to the jump pack: red positive to red positive, black negative to black negative.

Be aware that these wires are not a charging point for the LV battery. Applying 12V power to these wires will only pop the hood release, but now you can gain access to the LV battery inside. Open the hood and remove the trim panel which covers the LV battery. Locate the positive charge/jump post, and connect a suitable battery charger or jump pack to it. Attach the negative cable from the charger/jump pack to the beam in front of the LV battery. You should now be able to charge or jump the LV battery, and power on the ignition.

This video is sponsored by BendPak. It was originally posted on our sister site, Body Shop Business.

You May Also Like

Cal Ganda’s Continental journey: From manufacturing to aftermarket leadership

Cal Ganda’s path from Zimbabwe to leading aftermarket distribution at Continental’s ContiTech Group is a testament to seizing opportunities and embracing change. Arriving in the U.S. in 1998 for university, he ventured into food manufacturing post-graduation before diving into consulting. A chance encounter with Continental during a consulting project in Mexico led Cal to discover an opportunity

Cal Ganda’s path from Zimbabwe to leading aftermarket distribution at Continental’s ContiTech Group is a testament to seizing opportunities and embracing change. Arriving in the U.S. in 1998 for university, he ventured into food manufacturing post-graduation before diving into consulting.

A chance encounter with Continental during a consulting project in Mexico led Cal to discover an opportunity in tire assembly supervision in Charlotte. This marked the beginning of his journey with Continental, where he embraced various roles, from tire assembly to logistics and process engineering.

AMN Drivetime: Strategies for a changing aftermarket

Jeff Koviak describes his “master’s degree” in the automotive aftermarket as owning two muffler shops in Port Huron, Michigan, for a few years. He was at the ripe, young age of 24 and this stint came after he served as a Walker Exhaust territory manager with Tenneco in Detroit. Koviak calls that his first official

Drivetime_ Koviak-1400x700
Road to AAPEX season 2 finale: Where the road ends and the show begins

There’s a magical alchemy in how we get to where we’re going. A dot on the map, a full tank of gas and the open road. We navigate the twists and turns and arrive at our destination. The automotive aftermarket, however, has turned that process into a science with distribution delivering the right part to

Road to AAPEX season 2, ep. 9: The roads that connect us

The automotive aftermarket is about connections. Connections to the right parts, to the right places, to the right people. It’s the roads we travel down together that make us grow closer and bring us together. That’s the feeling that paves the Road to AAPEX as Babcox Media’s Joe Keene, an ASE-certified technician, traverses the Bonneville

Road to AAPEX Ep. 9
Watch: CVT modules and programming

CVTs usually will require a reset to the basic factory programming after repairing a major component. You can typically use a scan tool to help complete this. Watch the latest video from Transtar, above, for more. Related Articles – Watch: CVT diagnostic strategy and codes – Watch: The basics of CVT repair – Watch: Transmission

CVT-Fluid-Diagnostics-1400
Other Posts
Eaton four-speed electric transmission receives PACEpilot award

Eaton’s heavy-duty four-speed electrified vehicle transmission was named a 2024 Automotive News PACEpilot Innovation to Watch at an awards ceremony on April 29. Related Articles – ZF adds PowerLine transmission course to [pro]Academy Training program – Transend gets new website, branding – Report: U.S. automotive aftermarket industry grew 8.6% in 2023 Eaton said its EV

Eaton-Automotive-News-PACEpilot-award
BendPak announces upgraded Litestix work light

BendPak announced a new, upgraded version of its Litestix portable LED work light. The company says the new Litestix LS36SMDX model is now powered by a higher-capacity rechargeable battery and provides up to seven hours of continuous use on one charge. This represents another hour of performance over its predecessor, BendPak said. Related Articles –

BendPak founder Don Henthorn passes away

Don Henthorn, owner and founder of BendPak Inc., peacefully passed away at home Thursday, March 28, at the age of 85. Under his leadership, BendPak has grown from a small machine shop to one of the world’s leading manufacturers of car lifts and automotive service equipment. Related Articles – How much do gas prices affect the automotive

Don-Henthorn-BendPak_Passing-1400
Gray Tools introduces insulated hex bit socket set

Gray Tools has introduced a 16-piece insulated hex bit socket set. Made in the U.S.A., the set features both SAE and metric sizes, contained in a carrying case with a foam organizer. All pieces have dual-layer insulation, providing user protection up to 1,000 volts in a variety of electrical applications, the company said. Related Articles – K-Tool