Toyota A750E/F Small Parts - Transmission Digest

Main Navigation

Advertisement
Social Connect
Resources
Our Brand Family
Transmission Digest - Babcox Media
Helping transmission shops achieve successful and profitable operation.
Technical

Toyota A750E/F Small Parts

Toyota A750E/F There are some pitfalls that can trip you up with this valve body.

Avatar
By Jeff Parlee
Jeff Parlee is the Sonnax remanufactured valve body product support manager and member of the Sonnax TASC Force (Technical Automotive Specialties Committee), a group of recognized industry technical specialists, transmission rebuilders and Sonnax Industries Inc. technicians.
Published:
Toyota A750E/F Small Parts Body of Evidence Author: Jeff Parlee Subject Matter: Valve body Unit: A750E/F Vehicle Application: Toyota Issue: Avoiding assembly problems

Body of Evidence

  • Author: Jeff Parlee
  • Subject Matter: Valve body
  • Unit: A750E/F
  • Vehicle Application: Toyota
  • Issue: Avoiding assembly problems

There are some pitfalls that can trip you up with this valve body.

First, there are two different covers that can be found on top of the upper body. These covers have different casting numbers and different checkball configurations. The casting numbers are 89010 and 8850; I have seen only the 89010 checkball locations published. The checkball locations in the upper body are the same no matter which cover is on it (figures 1, 2 and 3).

Related Articles

The second gotcha is the retaining pin for the S1-solenoid sleeve. The S1 solenoid is held in place by a bolt, but the solenoid slides into a sleeve. The sleeve is held in the correct position by a 0.117-inch-diameter pin. The pin is held in place by the separator plate. When the valve body is disassembled and cleaned, the pin may fall out of the lower casting and not be noticed. The sleeve usually stays in place, making it easy to overlook the missing pin. When the S1 solenoid is installed, a bolt holds it in place. The solenoid prevents the sleeve from coming out when the oil circuit is energized, but it does not keep the sleeve from turning and blocking off the oil circuit to the S1 solenoid (figures 4 and 5).

The lower body also has a barrel-type screen. Place the open end of the screen toward the separator plate. The converter limit valve and spring are also situated in the lower body. Install the spring first, then the valve with the stem into the spring (Figure 4).

When assembling the valve body, install the manual valve into its bore before installing the SLU and SR solenoids (Figure 6).

Knowing the pitfalls before overhaul can make life a little easier.

Jeff Parlee is director of product support at ValveBody Xpress.

You May Also Like

CVT-Transmission-2
Featured

Sometimes, a diagnostic code is all you need

With ATSG having the opportunity to help shops solve problems, sometimes we get faced with some real doozies. A shop will call and give us a laundry list of DTCs, leaving us to think someone must have a bulkhead connector unplugged. We then go through the arduous task of deciding which codes prompted other codes

Wayne Colonna
By Wayne Colonna
Published:

With ATSG having the opportunity to help shops solve problems, sometimes we get faced with some real doozies. A shop will call and give us a laundry list of DTCs, leaving us to think someone must have a bulkhead connector unplugged. We then go through the arduous task of deciding which codes prompted other codes to set—we’re actually diagnosing diagnostic codes themselves at that point. So, when an issue comes up on our help line with codes that actually tell the story, it makes for a nice change, as well as a quick pathway to a repaired vehicle.

Read Full Article

More Technical Posts
10L80 and 10R80 pump gear differences

You may have seen an article in the August 2023 issue of Transmission Digest called “GM 10L80: A new kind of pump noise,” which goes over how the front cover housing in the 10L80 is fitted with a converter drive gear and idler gear. The idler gear drives the pump’s driven gear, and is press

By Wayne Colonna
Shift Pointers: What to do when the 62TE TRS tab breaks

How frustrating it is when on a hot summer day, as you go to open a nice cold can of your drink of choice, and the tab breaks off? You are outside, away from any tools to remedy the problem quickly. It now requires a MacGyver mentality looking around at the resources available to get

By Wayne Colonna
Going the extra mile: Proving your transmission repair suspicions

A 2003 Honda Pilot with a five-speed three-shaft transmission came into our shop with a customer concern that the vehicle had no power, and the “D” light was flashing. I first did a scan for codes to see what it came up with, and the scan tool returned four DTCs: P1298 (ELD voltage high), P0135 (H02S

By Paul Loch
RRfeature-1400
Diagnosing Ford 10R60, 10R80 and 10R140 series speed sensor issues

Ford 10-speed 10R series transmissions utilize four two-wire, Hall-effect sensors — TSS, ISSA2, ISSAB and OSS — for providing speed signals to PCM or TCM. They are supplied nine volts by a PCM or TCM and assist in the control of clutch apply/release timing that is used in determining shift quality, including TCC. Related Articles

By Jim Mobley

Other Posts

Shift Pointers: Failures caused by incorrect tire sizes

For years ATSG has produced a wide range of issues related to improper tire sizes on vehicles. Even under-inflated tires have been known to cause issues. Problems such as premature failure with an active 4WD transfer case will occur with incorrect tire sizes. Related Articles – Valve body and component suppliers: A comprehensive list –

By Wayne Colonna
Shift-Pointers-Jan-Figure-1-1400
Understanding lube flow control valves in Toyota/Lexus UA/UB80 transmissions

The Toyota/Lexus UA80 and UB80 transmissions first came out in 2017 in Highlanders and Siennas. The UA80 is used in V6 applications, and the UB80 is paired with four-cylinder versions. They have been called Toyota New Global Architecture type transmissions, and alternately referred to as the “Direct Shift 8AT” eight-speed automatic transmission. This transmission was

By Jim Dial
Tasc-Tip-December-Figure-1---LFC-Valve-OE-Partial-Circuit-Diagram-1400
How reading through service bulletins can turn a technician into the customer’s hero

Over the last 28 years of being a technician, I have developed the habit of checking for and reading technical service bulletins at the forefront of the diagnostic process, especially when an unfamiliar vehicle exhibiting blatant or straightforward concerns comes into the shop. I have found many valuable nuggets of information while reading over these

By Kevin Wayne
Sometimes, you should sweat the small stuff

It’s a common phrase: There may have been a time when you worried about something, and someone who knew what you are going through said, “Hey, don’t sweat the small stuff.” Sometimes, this may be good advice. But other times, it may be wise to handle the small stuff before it becomes bigger “stuff.”  Related

By Wayne Colonna