Technician Turned Sleuth - Transmission Digest

Technician Turned Sleuth

How often have you accepted a repair knowing that others have been involved? How often are you required to channel your inner Sherlock Holmes? Two recent repair jobs led me to unusual conclusions. One of my customers brought in a Nissan Sentra that had a habit of blowing its interior-lamp fuse. She would replace the fuse, and then it could fail within hours, or it could take days before it popped. Most of the time when I see blown fuses, there is a direct connection to either rubbed factory harnesses that aren’t routed with enough free play – sometimes accompanied by a TSB – or it is due to the intervention of human hands during a repair or modification, such as an aftermarket installation.

Tech to Tech

  • Author: Brian Manley
  • Subject Matter: Diagnosis
  • Vehicle Applications: Nissan Sentra; Jeep Wrangler X
  • Issue: Blown fuse; soft brake pedal

Inner Sherlock Holmes finally solves the mystery

How often have you accepted a repair knowing that others have been involved? How often are you required to channel your inner Sherlock Holmes? Two recent repair jobs led me to unusual conclusions.

One of my customers brought in a Nissan Sentra that had a habit of blowing its interior-lamp fuse. She would replace the fuse, and then it could fail within hours, or it could take days before it popped.

Most of the time when I see blown fuses, there is a direct connection to either rubbed factory harnesses that aren’t routed with enough free play – sometimes accompanied by a TSB – or it is due to the intervention of human hands during a repair or modification, such as an aftermarket installation.

My initial investigation did not reveal excess current flowing through this circuit, and all my coaxing could not cause my readings to change. Of course, driving the car to lunch caused excess current flow and a blown fuse! My frustration – and we have all been there – was that it was so intermittent that I couldn’t disconnect parts of the circuit and immediately see which branch contained the short circuit.

The first move I made was to carefully scrutinize the “room lamp” at the center of the car – just to see whether some of the moving parts had come loose – and when I saw nothing shorting, I removed the entire lamp assembly for inspection. I did not find what I had hoped. So, after studying the schematic (Figure 1), I decided to disconnect the map-light branch, install a new fuse and test-drive. Since it did not pop the fuse, I sent the vehicle home with my customer for a longer test, and the fuse failed the next day.

I was becoming pretty familiar with this Nissan, so I had my customer drive in for a fresh fuse and a new disconnect; this time I unplugged the time-control unit.

Several days later my customer came back in, and I verified that the fuse was intact, but I would only be guessing to blame the time-control unit – and it was hard to find and a wee bit expensive – so I plugged the unit back in and disconnected the room-lamp wire near the left kick panel. Several days later: no blown fuse!

Finally, I felt confident that I had narrowed down one branch as the root cause! Since I had ruled out the overhead switch/lamp assembly as a culprit, I began to disassemble trim panels: The left kick panel all the way up the inside of the “A” pillar, and what I saw in figures 2 and 3 surprised me! Figure 2 shows a twisted and mangled wire in a location that had no screws or moving parts. I could see where the B+ wire was intermittently rubbing against the ground.

What could have caused such damage? Inside the A-pillar trim piece held the clue: There were shards of glass and a few strands of copper. I called my customer, who verified that she had a windshield replaced “a while back” and that she did not connect the two events because they occurred so far apart. I guess those windshield-removal tools can slip under trim panels and cause damage that goes unnoticed.

My second customer had a late-model Jeep Wrangler X with a complaint of a low, spongy brake pedal. He confirmed the fact that he had recently performed the brake job himself but felt confident in the quality of the parts and the care of his installation. I told him we would find out what was causing his low and spongy pedal.

The first thing I did was drive his Jeep, and the pedal felt as if there were air in the system. It was odd: I could “stab” the brake pedal and get the Jeep to stop very quickly, even from 40 mph, but the excess pedal travel and spongy feel were disconcerting. It finally “grabbed” about halfway down, which was lower than I am used to with these four-wheel-disc systems.

I perused my information system to confirm that this Jeep didn’t require any special procedures after pad and rotor replacement. It was a straightforward system with anti-lock and four-wheel disc. We pulled the wheels for inspection and found nothing out of the ordinary: My customer had replaced front and rear sets of pads and had his rotors machined, which we verified as being still within specification. With no obvious parts or installation issues, we decided to bleed the brake system.

At this point, I truly felt confident that a bleeding would cure the symptoms and we’d have a nice, firm, tall brake pedal. Of course, there was no change in the pedal feel or the operation of the brakes.

Next, I decided on a complete disassembly of ALL components that my customer had his hands on, and that’s where we found what you see in Figure 4: A bent inboard brake pad! In fact, both inboard rear pads were bent in the same place. Now we were onto something!

After disassembling components, I could easily see the bend (Figure 5) and could see where the new pad was catching in the caliper because of a manufacturing flaw or an installation error.

I surmised that the bend in both pads caused a spring-like action, preventing immediate application of those pads but allowing full brake action once the hydraulic pressure overcame the unintentional “spring.” This is what caused the spongy feel and low pedal but the ultimate “good” braking once the pedal was applied hard enough. Kind of an interesting root cause!

Just as the fictional character in Sir Arthur Conan Doyle’s books, Sherlock Holmes, would say: “When you have eliminated the impossible, whatever remains, however improbable, must be the truth!”

The truth in both of these repairs came after I had definitely eliminated all the anticipated root causes. These conclusions were two that I had just flat-out never seen before. I had not anticipated the wire damage from a windshield repair, but it certainly supports my theory that many short circuits are due to human intervention after the vehicle leaves its production line. This bent pad was tough to see with the calipers installed; it just didn’t jump right out at me. But since this brake system was such a basic design, the probable list of root causes quickly vanished, leaving me with a fairly improbable root cause. However improbable, the truth in both cases fixed both vehicles.

Brian Manley is a vocational automotive instructor for the Cherry Creek school district in Aurora, Colo. He is an ASE master certified automobile technician and a former member of the National Automotive Technicians Education Foundation (NATEF) board of trustees. You can reach him at [email protected].

This copyrighted article is reprinted with the permission of AutoInc., the official publication of the Automotive Service Association (ASA). To learn more about ASA and its commitment to independent automotive-service and repair professionals, visit www.ASAshop.org or call 800-272-7467.

You May Also Like

Going the extra mile: Proving your transmission repair suspicions

A 2003 Honda Pilot with a five-speed three-shaft transmission came into our shop with a customer concern that the vehicle had no power, and the “D” light was flashing. I first did a scan for codes to see what it came up with, and the scan tool returned four DTCs: P1298 (ELD voltage high), P0135 (H02S

RRfeature-1400

A 2003 Honda Pilot with a five-speed three-shaft transmission came into our shop with a customer concern that the vehicle had no power, and the “D” light was flashing. I first did a scan for codes to see what it came up with, and the scan tool returned four DTCs: P1298 (ELD voltage high), P0135 (H02S [S1] heater failure), P0141 (H02S [S2] heater circuit malfunction), P0748 (clutch pressure control solenoid valve “A” failure), and the ubiquitous P0700 (AT system malfunction) code. (See Figure 1). 

Diagnosing Ford 10R60, 10R80 and 10R140 series speed sensor issues

Ford 10-speed 10R series transmissions utilize four two-wire, Hall-effect sensors — TSS, ISSA2, ISSAB and OSS — for providing speed signals to PCM or TCM. They are supplied nine volts by a PCM or TCM and assist in the control of clutch apply/release timing that is used in determining shift quality, including TCC. Related Articles

Jatco JF613E transmission quick reference material

For those working on the Jatco JR613E transmission, a widespread transmission with plenty of applications, the following should be a helpful guide. Related Articles – Hidden problems: Three tales of electrical issues – Easy TH400, 4L80-E reverse servo setup: Craft your own tool – Outgrowing the walls: The story of EVT Transmission Parts Domestic and

Easy TH400, 4L80-E reverse servo setup: Craft your own tool

While not as sensitive as some shifting bands, the Reverse band adjustment on a TH400 or 4L80-E transmission is critical, and failure to get it right has tripped up even the best builders. There is nothing worse than getting the transmission installed, putting it in Reverse and then not going anywhere or having no engine

Spotting different 68RFE designs through the years to avoid issues

The Chrysler 68RFE has had several changes through the years. Its four-speed predecessor began with a noisy solenoid pack identified by a black colored pass-through case connector (seen in Figure 1).  Related Articles – Understanding lube flow control valves in Toyota/Lexus UA/UB80 transmissions – How reading through service bulletins can turn a technician into the

Other Posts

Shift Pointers: Focused DTCs

On occasions when a vehicle’s computer system detects an error, it can set an array of diagnostic trouble codes. The variety and quantity of them require the ability to diagnose diagnostic codes, so it’s nice when codes set that point directly to the problem.  Related Articles – Fabricating frictions: Keeping ahead of the curve at

Manual clutch repair and diagnostics

Manual gearboxes are relatively trouble-free and long-lived, provided that they are not abused too severely. The clutch, however, is a wear component. With every shift, the clutch must be disengaged and engaged. Stop-and-go driving in heavy traffic is especially hard on a clutch because the driver is always riding the clutch pedal. After millions of

Manual-Transmission
Looking deeper: Telling apart electrical issues and parts issues

We see such a variety of transmission problems these days, and all the electronics involved today certainly have added a whole new crop of potential issues. Even though a significant part of our diagnostic process is geared towards electrical issues, there are still times when the problem is simple and not related to electronics at

RR-Tech-Nov-FIG-1
Manual transmissions in 2023: Some are still sticking with it

Over the past 25 years, a combination of driver preference and fuel economy requirements have resulted in a marked decrease in the number of vehicles in the U.S. fleet that come equipped with a manual transmission. One can wax nostalgic for the “car guy” discussions from 40 or 50 years ago that included terms like