Video: How to use Evaporator and Heater Foam Cleaners - Transmission Digest

Video: How to use Evaporator and Heater Foam Cleaners

This video covers the steps on applying Kool-It Evaporator and Heater Foam Cleaners. The full text of this video, sponsored by Lubegard, is below:

Welcome to how to apply Kool-It Evaporator and Heater Foam Cleaner by Lubegard.

Did you know that air quality inside a vehicle can be five times worse than outside air? Foul odors in evaporator and heater cores as a result of inanimate allergens and contaminants can be easily flushed away without any drilling or special equipment. It’s quick, easy and highly effective.

Lubegard’s Evaporator and Heater Foam Cleaner is odor neutralizing and leaves behind a clean, fresh scent.

Kool-It is packaged with a 30-inch long hose with a special tip to help you break through minor clogs and  applies our product directly to the HVAC system. It’s super foaming action flushes out and neutralizes unwanted contaminants.

Before you begin, you need to prepare by first finding a waste container to have nearby. Next you will need to gain access to the evaporator/heater core drain which typically is underneath the vehicle, next to the engine compartment side of the firewall. It may be accessed by jacking up the car, and please, always back up your jack with a jack stand, ramps or a secondary fail safe.

A simple way to locate your evaporator drain is to allow your vehicle to run in A/C mode until you can see where the condensate water is dripping out of the drain tube underneath the vehicle.

Once you’ve located the drain tube, start by shaking the can well. Next, snake the foam cleaner hose up the tube as far as it allows. You are now ready to administer the cleaner.

Begin emptying the can contents into the evaporator/heater core, and remove the hose when can is empty. Be sure to place a waste container underneath the drain to catch the dirty liquid. We’re going to dispense a separate can into this container so you can see a representation of what is actually happening inside of an evaporator/heater core.

After allowing the product to work for 15 minutes, turn the vehicle fan on to the lowest setting, at a ambient temperature and let it run for five minutes. The foam will collapse and drain back out of the drain plug, removing contaminants causing odor. The odor eliminating formula can last up to six months.

While the preferred method is application via the drain tube, Lubegard foam cleaner can also be applied through the air cabin filter, or through the interior vents depending on the ventilation set-up. If applying through the vents, be absolutely  sure that the vent goes directly into the evaporator core. Do not to apply Kool-It in any vent that would have contact with any electronic system. 

Also, be careful with getting foam on the interior and wipe away excess as soon as possible. If applying through the air cabin filter, remove cabin air filter before installing Kool-It.

Kool-It can be used in cars, trucks, vans, RVs or any other HVAC system that is enclosed and prone to odor.

Kool-It is electric vehicle safe and is currently approved and recommended by a major EV vehicle manufacturer as the solution to to eliminate smells in the AC.

This video is sponsored by Lubegard.

You May Also Like

Sponsored video: How to apply Lubegard CVT Recharge

In this sponsored video, find a walkthrough on how to apply Lubegard’s CVT Recharge. The text of the video is below: CVT Recharge was formulated and designed specifically to restore performance to additive-depleted, continuously variable transmission (CVT) fluid when problems occur before normal fluid change intervals. Let’s take a look. Lubegard’s CVT Recharge is a

Lubegard-CVT-Recharge

In this sponsored video, find a walkthrough on how to apply Lubegard's CVT Recharge. The text of the video is below:

CVT Recharge was formulated and designed specifically to restore performance to additive-depleted, continuously variable transmission (CVT) fluid when problems occur before normal fluid change intervals. Let’s take a look.

Sponsored video: Lubegard engine oil protectant for turbocharged engines (LSPI)

In this sponsored video, Lubegard highlights the features and benefits of its engine oil protectant for turbocharged engines with LSPI (low-speed pre-ignition), one of the most common problems found in today’s turbocharged gasoline engines, and one you might experience in your shop.

Lubegard-video-preview
Video: Instant shudder fix

This sponsored video shows users how to apply Instant Shudder Fixx by Lubegard.

Video: Lubegard Limited Slip Supplement overview

This sponsored video highlights the Lubegard Limited Slip Supplement, a concentrated friction modifier formulated specifically for eliminating noise, and chatter, and clutch-type limited slip differentials.

Video: Rust and corrosion preventive oil

This sponsored video highlights Rustgard, a rest and corrosion prevention oil from Lubegard.

Other Posts

ILI introduces Lubegard engine oil protectant for turbocharged engines

International Lubricants, Inc. (ILI), makers of Lubegard automotive branded lubricants, announced the introduction of Lubegard Engine Oil Protectant for Turbocharged Engines (LSPI), available exclusively at AutoZone as of this February. Related Articles – Force Control Industries releases transmission fluid for oil shear clutch and brake applications  – TransGo introduces 62TE high pressure kit for vans

Lubegard-1400
Sponsored video: Aluminum protectant

This video is sponsored by Lubegard. The text of the video is below. Did you know that automatic transmission fluid and other hydraulic fluids do not protect aluminum from wear? This means that aluminum that is in contact with steel or other aluminum parts such as valve bodies, servo boards and pistons is not protected

Sponsored video: Kooler Kleen product overview

This video is sponsored by Lubegard. The text of the video is below. Welcome to the Lubegard Kooler Kleen Transmission Kooler Line Flush with two-in-one fitting, part number 19001-UNV product overview. OEMs state that the transmission oil coolers must be flushed whenever transmissions are replaced, or contaminants, such as metal particles and clutch material, may

lubegard kooler kleen
Lubegard introduces Rustgard Rust & Corrosion Preventive Oil

International Lubricants, Inc. (ILI), makers of Lubegard automotive branded lubricants, announced the introduction of Lubegard Rustgard Rust & Corrosion Preventive Oil, available this November. Related Articles – American Powertrain introduces ProTwin disc clutch for GM, Ford and Mopar – Sonnax introduces Smart-Tech clutch kit for GM 4L series – Snap-on debuts new general service tool